메뉴 바로가기본문 바로가기

답변[re] G054P 리눅스 사용방법 알려주세요

2007.01.02조회 1,729

참고하시길...

*
* Ralink Tech Inc.
*
* http://www.ralinktech.com
*

======================================================================= ModelName:
===========
RT61 Wireless Lan Linux Driver


======================================================================= Driver lName:
===========
rt61.o/rt61.ko


======================================================================= Supporting Kernel:
===================
linux kernel 2.4 and 2.6 series. Tested in Redhat 7.3 or later.


======================================================================= Description:
=============
This is a linux device driver for Ralink RT61 a/b/g WLAN Card.


======================================================================= Contents:
=============
Makefile.4                : Makefile for kernel 2.4 series Makefile.6                : Makefile for kernel 2.6 series Makefile.RTL865x        : Makefile for big endian platform
*.c                                        : c files
*.h                                        : header files


======================================================================= Features:
==========
   This driver implements basic IEEE802.11. Infrastructure and adhoc mode with
   open or shared or WPA-PSK or WPA2-PSK authentication method.
   NONE, WEP, TKIP and AES encryption.


======================================================================= Build Instructions:  
====================

1> $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz
    go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.
    
2> $cp Makefile.4  ./Makefile       # [kernel 2.4]
    or
   $cp Makefile.6  ./Makefile       # [kernel 2.6]
    or
   $cp Makefile.RTL865x ./Makefile  #  big endian platform
  
3> [kernel 2.4]
    $chmod 755 Configure
    $make config         # config build linux os version

4> $make all            # compile driver source code

5> $cp rt2561.bin /etc/Wireless/RT61STA/        # copy firmware
   $cp rt2561s.bin /etc/Wireless/RT61STA/
   $cp rt2661.bin /etc/Wireless/RT61STA/

6>  $dos2unix rt61sta.dat
    $cp rt61sta.dat  /etc/Wireless/RT61STA/rt61sta.dat      
    # !!!check if it is a binary file before loading !!!  
    
7> $load                
    #[kernel 2.4]
    #    $/sbin/insmod rt61.o
    #    $/sbin/ifconfig ra0 inet YOUR_IP up
        
    #[kernel 2.6]
    #    $/sbin/insmod rt61.ko
    #    $/sbin/ifconfig ra0 inet YOUR_IP up

        
Note: Script functionality:
load            load module to kernel unload          unload module from kernel Configure       retrieve linux version


======================================================================= CONFIGURATION:  
====================
RT61 driver can be configured via following interfaces, i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file,
     (iv)RaConfig61

i)  iwconfig comes with kernel.   ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details. iii)copy configuration file "rt61sta.dat" to /etc/Wireless/RT61STA/rt61sta.dat. iv) RaConfig61 is utility for rt61.
          
Configuration File : rt61sta.dat
---------------------------------------
# Copy this file to /etc/Wireless/RT61STA/rt61sta.dat
# This file is a binary file and will be read on loading rt.o module.
#
# Use "vi -b rt61sta.dat" to modify settings according to your need.
#
# 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure
# 2.) set Channel to "0" for auto-select on Infrastructure mode
# 3.) set SSID for connecting to your Accss-point.
# 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE"
# 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES"
# for more information refer to the Readme file.
#
# The word of "[Default]" must not be removed
[Default]
CountryRegion=0
CountryRegionABand=7
WirelessMode=0
SSID=AP350
NetworkType=Infra
Channel=0
AuthMode=OPEN
EncrypType=NONE
DefaultKeyID=1
Key1Type=0
Key1Str=0123456789
Key2Type=0
Key2Str=
Key3Type=0
Key3Str=
Key4Type=0
Key4Str=
WPAPSK=abcdefghijklmnopqrstuvwxyz TxBurst=0 PktAggregate=0 WmmCapable=0 APSDCapable=0 APSDAC=0;0;0;0 BGProtection=0 ShortSlot=0 IEEE80211H=0 TxRate=0 RTSThreshold=2347 FragThreshold=2346 PSMode=CAM TxPreamble=0

-----------------------------------------------
*NOTE:
WMM parameters:
1.) WmmCapable                        
    Set it as 1 to turn on WMM Qos support
        
2.) APSDCapable
        Set it as 1 to use automatic power-save delivery(APSD) on an Non-AP QSTA

3.) APSDAC
        Set ACs corresponding BE, BK, VI and VO as delivery-enabled or delivery-disabled

        
All WMM parameters do not support iwpriv command but WmmCapable,
        please store all parameter to rt61sta.dat, and restart driver.         

----------------------------------------------- syntax is 'Param'='Value' and describes below.

1. CountryRegion=value                                
        value
                0: use 1 ~ 11 Channel
                1: use 1 ~ 13 Channel
                2: use 10, 11 Channel
                3: use 10 ~ 13 Channel
                4: use 14 Channel
                5: use 1 ~ 14 Channel
                6: use 3 ~ 9 Channel
                7: use 5 ~ 13 Channel
                                                          
2. CountryRegionABand=value                                                              
        value        
                0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel
                1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel
                2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel
                3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel
                4: use 149, 153, 157, 161, 165 Channel
                5: use 149, 153, 157, 161 Channel
                6: use 36, 40, 44, 48 Channel
                7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel
                8: 52, 56, 60, 64 Channel
                9: 34, 38, 42, 46 Channel
                10: 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 Channel
                                                  
3. SSID=value                        
        value
                0~z, 1~32 ascii characters.
                            
4. WirelessMode=value
        value        
                0: 11b/g mixed
                1: 11B only
                2: 11A only          //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)
                3: 11a/b/g mixed     //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)
                4: 11G only
                
5. TxRate=value
        value
                 0: Auto            //WirelessMode=0~4        
                 1: 1 Mbps                 //WirelessMode=0 or 1 or 3
         2: 2 Mbps                 //WirelessMode=0 or 1 or 3
         3: 5.5 Mbps         //WirelessMode=0 or 1 or 3
         4: 11 Mbps         //WirelessMode=0 or 1 or 3
         5: 6  Mbps          //WirelessMode=0 or 2 or 3 or 4
         6: 9  Mbps          //WirelessMode=0 or 2 or 3 or 4
         7: 12 Mbps          //WirelessMode=0 or 2 or 3 or 4
         8: 18 Mbps          //WirelessMode=0 or 2 or 3 or 4
         9: 24 Mbps          //WirelessMode=0 or 2 or 3 or 4
        10: 36 Mbps          //WirelessMode=0 or 2 or 3 or 4
        11: 48 Mbps          //WirelessMode=0 or 2 or 3 or 4
        12: 54 Mbps          //WirelessMode=0 or 2 or 3 or 4
                                              
6. Channel=value
        value
                depends on CountryRegion or CountryRegionABand
                            
7. BGProtection=value
        value
                0: Auto
                1: Always on
                2: Always off
                            
8. TxPreamble=value
          value
                0:Preamble Long
                1:Preamble Short
                2:Auto
                            
9. RTSThreshold=value
        value
                1~2347                                                      
                                                                  
10. FragThreshold=value
        value               
                256~2346
                            
11. TxBurst=value
        value
                0: Disable
                1: Enable

12. NetworkType=value                            
        value
                Infra: infrastructure mode
               Adhoc: adhoc mode
                                                                                                                                                                                                                          
13. AuthMode=value
        value
                OPEN                 For open system        
                SHARED                  For shared key system        
                WEPAUTO     Auto switch between OPEN and SHARED
                WPAPSK      For WPA pre-shared key  (Infra)
                WPA2PSK     For WPA2 pre-shared key (Infra)
                WPANONE                For WPA pre-shared key  (Adhoc)
                WPA         Use WPA_Supplicant
                WPA2        Use WPA_Supplicant

14. EncrypType=value
        value
                NONE                For AuthMode=OPEN                    
                WEP                        For AuthMode=OPEN or AuthMode=SHARED
                TKIP                For AuthMode=WPAPSK or WPA2PSK                    
                AES                        For AuthMode=WPAPSK or WPA2PSK                    
                
15. DefaultKeyID=value
        value
                1~4

16. Key1=value
    Key2=value
    Key3=value
    Key4=value
        value
                10 or 26 hexadecimal characters eg: 012345678
        5 or 13 ascii characters eg: passd
    (usage : "iwpriv" only)    

17. Key1Type=vaule
    Key2Type=value
    Key3Type=vaule
    Key4Type=vaule
    value
                0   hexadecimal type
                1   assic type
    (usage : reading profile only)

18. Key1Str=value
    Key2Str=value
    Key3Str=vaule
    Key4Str=vaule
    value
                10 or 26 characters (key type=0)
                5 or 13 characters  (key type=1)
    (usage : reading profile only)        

19. WPAPSK=value                      
        value
                8~63 ASCII                  or
                64 HEX characters

20. PktAggregate=value
        value
                0: Disable
                1: Enable when the peer supports it
                                                                                                                                
21. WmmCapable=value
        value
                0: Disable WMM
                1: Enable WMM
        
22. PSMode=value
    value
            CAM                            Constantly Awake Mode
                Fast_PSP                Power Save Mode
                
23. IEEE80211H=value
        value
                0:        Disable
                1:        Enable        Spectrum management
                (This field can be enable only in A band)
                
24. FastRoaming=value                                
        value
                0: Disable Fast Roaming
                1: Enable Fast Roaming

25. RoamThreshold=value
        value [Valid on FastRoaming=1]              
                60~90

26. APSDCapable=value
        value [Valid on WmmCapable=1]
                0: Disable APSD
                1: Enable APSD

27. APSDAC=value
        value [Valid on APSDCapable=1]
                0: Delivery-disabled AC
                1: Delivery-enabled AC
        
                //========================//
                AC_BE  AC_BK  AC_VI  AC_VO
                {0, 1};{0, 1};{0, 1};{0, 1}
        //========================//



MORE INFORMATION
================================================================================= If you want for rt61 driver to auto-load at boot time:
A) choose ra0 for first RT61 WLAN card, ra1 for second RT61 WLAN card, etc.

B) go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.
   $make install

NOTE:
        if you use dhcp,
        add this line
        BOOTPROTO='dhcp'
        in the file ifcfg-ra0 .


*C) To ease the Default Gateway setting,
    add the line
    GATEWAY=x.x.x.x  
    in /etc/sysconfig/network

  
감사합니다.

질문

QnA
제  목[re] G054P 리눅스 사용방법 알려주세요
이름오*****
제품명86
인터넷 회선XPEED 프라임
목록보기
참고하시길... * * Ralink Tech Inc. * * http://www.ralinktech.com * ======================================================================= ModelName: =========== RT61 Wireless Lan Linux Driver ======================================================================= Driver lName: =========== rt61.o/rt61.ko ======================================================================= Supporting Kernel: =================== linux kernel 2.4 and 2.6 series. Tested in Redhat 7.3 or later. ======================================================================= Description: ============= This is a linux device driver for Ralink RT61 a/b/g WLAN Card. ======================================================================= Contents: ============= Makefile.4                : Makefile for kernel 2.4 series Makefile.6                : Makefile for kernel 2.6 series Makefile.RTL865x        : Makefile for big endian platform *.c                                        : c files *.h                                        : header files ======================================================================= Features: ==========    This driver implements basic IEEE802.11. Infrastructure and adhoc mode with    open or shared or WPA-PSK or WPA2-PSK authentication method.    NONE, WEP, TKIP and AES encryption. ======================================================================= Build Instructions:   ==================== 1> $tar -xvzf RT61_Linux_STA_Drv_x.x.x.x.tar.gz     go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.      2> $cp Makefile.4  ./Makefile       # [kernel 2.4]     or    $cp Makefile.6  ./Makefile       # [kernel 2.6]     or    $cp Makefile.RTL865x ./Makefile  #  big endian platform    3> [kernel 2.4]     $chmod 755 Configure     $make config         # config build linux os version 4> $make all            # compile driver source code 5> $cp rt2561.bin /etc/Wireless/RT61STA/        # copy firmware    $cp rt2561s.bin /etc/Wireless/RT61STA/    $cp rt2661.bin /etc/Wireless/RT61STA/ 6>  $dos2unix rt61sta.dat     $cp rt61sta.dat  /etc/Wireless/RT61STA/rt61sta.dat           # !!!check if it is a binary file before loading !!!        7> $load                     #[kernel 2.4]     #    $/sbin/insmod rt61.o     #    $/sbin/ifconfig ra0 inet YOUR_IP up              #[kernel 2.6]     #    $/sbin/insmod rt61.ko     #    $/sbin/ifconfig ra0 inet YOUR_IP up          Note: Script functionality: load            load module to kernel unload          unload module from kernel Configure       retrieve linux version ======================================================================= CONFIGURATION:   ==================== RT61 driver can be configured via following interfaces, i.e. (i)"iwconfig" command, (ii)"iwpriv" command, (iii) configuration file,      (iv)RaConfig61 i)  iwconfig comes with kernel.   ii) iwpriv usage, please refer to file "iwpriv_usage.txt" for details. iii)copy configuration file "rt61sta.dat" to /etc/Wireless/RT61STA/rt61sta.dat. iv) RaConfig61 is utility for rt61.            Configuration File : rt61sta.dat --------------------------------------- # Copy this file to /etc/Wireless/RT61STA/rt61sta.dat # This file is a binary file and will be read on loading rt.o module. # # Use "vi -b rt61sta.dat" to modify settings according to your need. # # 1.) set NetworkType to "Adhoc" for using Adhoc-mode, otherwise using Infrastructure # 2.) set Channel to "0" for auto-select on Infrastructure mode # 3.) set SSID for connecting to your Accss-point. # 4.) AuthMode can be "WEPAUTO", "OPEN", "SHARED", "WPAPSK", "WPA2PSK", "WPANONE" # 5.) EncrypType can be "NONE", "WEP", "TKIP", "AES" # for more information refer to the Readme file. # # The word of "[Default]" must not be removed [Default] CountryRegion=0 CountryRegionABand=7 WirelessMode=0 SSID=AP350 NetworkType=Infra Channel=0 AuthMode=OPEN EncrypType=NONE DefaultKeyID=1 Key1Type=0 Key1Str=0123456789 Key2Type=0 Key2Str= Key3Type=0 Key3Str= Key4Type=0 Key4Str= WPAPSK=abcdefghijklmnopqrstuvwxyz TxBurst=0 PktAggregate=0 WmmCapable=0 APSDCapable=0 APSDAC=0;0;0;0 BGProtection=0 ShortSlot=0 IEEE80211H=0 TxRate=0 RTSThreshold=2347 FragThreshold=2346 PSMode=CAM TxPreamble=0 ----------------------------------------------- *NOTE: WMM parameters: 1.) WmmCapable                             Set it as 1 to turn on WMM Qos support          2.) APSDCapable         Set it as 1 to use automatic power-save delivery(APSD) on an Non-AP QSTA 3.) APSDAC         Set ACs corresponding BE, BK, VI and VO as delivery-enabled or delivery-disabled          All WMM parameters do not support iwpriv command but WmmCapable,         please store all parameter to rt61sta.dat, and restart driver.          ----------------------------------------------- syntax is 'Param'='Value' and describes below. 1. CountryRegion=value                                         value                 0: use 1 ~ 11 Channel                 1: use 1 ~ 13 Channel                 2: use 10, 11 Channel                 3: use 10 ~ 13 Channel                 4: use 14 Channel                 5: use 1 ~ 14 Channel                 6: use 3 ~ 9 Channel                 7: use 5 ~ 13 Channel                                                            2. CountryRegionABand=value                                                                       value                         0: use 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 Channel                 1: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 Channel                 2: use 36, 40, 44, 48, 52, 56, 60, 64 Channel                 3: use 52, 56, 60, 64, 149, 153, 157, 161 Channel                 4: use 149, 153, 157, 161, 165 Channel                 5: use 149, 153, 157, 161 Channel                 6: use 36, 40, 44, 48 Channel                 7: use 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 Channel                 8: 52, 56, 60, 64 Channel                 9: 34, 38, 42, 46 Channel                 10: 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 Channel                                                    3. SSID=value                                 value                 0~z, 1~32 ascii characters.                              4. WirelessMode=value         value                         0: 11b/g mixed                 1: 11B only                 2: 11A only          //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)                 3: 11a/b/g mixed     //Support in RfIcType=1(id=RFIC_5225) or RfIcType=2(id=RFIC_5325)                 4: 11G only                  5. TxRate=value         value                  0: Auto            //WirelessMode=0~4                          1: 1 Mbps                 //WirelessMode=0 or 1 or 3          2: 2 Mbps                 //WirelessMode=0 or 1 or 3          3: 5.5 Mbps         //WirelessMode=0 or 1 or 3          4: 11 Mbps         //WirelessMode=0 or 1 or 3          5: 6  Mbps          //WirelessMode=0 or 2 or 3 or 4          6: 9  Mbps          //WirelessMode=0 or 2 or 3 or 4          7: 12 Mbps          //WirelessMode=0 or 2 or 3 or 4          8: 18 Mbps          //WirelessMode=0 or 2 or 3 or 4          9: 24 Mbps          //WirelessMode=0 or 2 or 3 or 4         10: 36 Mbps          //WirelessMode=0 or 2 or 3 or 4         11: 48 Mbps          //WirelessMode=0 or 2 or 3 or 4         12: 54 Mbps          //WirelessMode=0 or 2 or 3 or 4                                                6. Channel=value         value                 depends on CountryRegion or CountryRegionABand                              7. BGProtection=value         value                 0: Auto                 1: Always on                 2: Always off                              8. TxPreamble=value           value                 0:Preamble Long                 1:Preamble Short                 2:Auto                              9. RTSThreshold=value         value                 1~2347                                                                                                                          10. FragThreshold=value         value                                256~2346                              11. TxBurst=value         value                 0: Disable                 1: Enable 12. NetworkType=value                                     value                 Infra: infrastructure mode                Adhoc: adhoc mode                                                                                                                                                                                                                            13. AuthMode=value         value                 OPEN                 For open system                         SHARED                  For shared key system                         WEPAUTO     Auto switch between OPEN and SHARED                 WPAPSK      For WPA pre-shared key  (Infra)                 WPA2PSK     For WPA2 pre-shared key (Infra)                 WPANONE                For WPA pre-shared key  (Adhoc)                 WPA         Use WPA_Supplicant                 WPA2        Use WPA_Supplicant 14. EncrypType=value         value                 NONE                For AuthMode=OPEN                                     WEP                        For AuthMode=OPEN or AuthMode=SHARED                 TKIP                For AuthMode=WPAPSK or WPA2PSK                                     AES                        For AuthMode=WPAPSK or WPA2PSK                                      15. DefaultKeyID=value         value                 1~4 16. Key1=value     Key2=value     Key3=value     Key4=value         value                 10 or 26 hexadecimal characters eg: 012345678         5 or 13 ascii characters eg: passd     (usage : "iwpriv" only)     17. Key1Type=vaule     Key2Type=value     Key3Type=vaule     Key4Type=vaule     value                 0   hexadecimal type                 1   assic type     (usage : reading profile only) 18. Key1Str=value     Key2Str=value     Key3Str=vaule     Key4Str=vaule     value                 10 or 26 characters (key type=0)                 5 or 13 characters  (key type=1)     (usage : reading profile only)         19. WPAPSK=value                               value                 8~63 ASCII                  or                 64 HEX characters 20. PktAggregate=value         value                 0: Disable                 1: Enable when the peer supports it                                                                                                                                  21. WmmCapable=value         value                 0: Disable WMM                 1: Enable WMM          22. PSMode=value     value             CAM                            Constantly Awake Mode                 Fast_PSP                Power Save Mode                  23. IEEE80211H=value         value                 0:        Disable                 1:        Enable        Spectrum management                 (This field can be enable only in A band)                  24. FastRoaming=value                                         value                 0: Disable Fast Roaming                 1: Enable Fast Roaming 25. RoamThreshold=value         value [Valid on FastRoaming=1]                               60~90 26. APSDCapable=value         value [Valid on WmmCapable=1]                 0: Disable APSD                 1: Enable APSD 27. APSDAC=value         value [Valid on APSDCapable=1]                 0: Delivery-disabled AC                 1: Delivery-enabled AC                          //========================//                 AC_BE  AC_BK  AC_VI  AC_VO                 {0, 1};{0, 1};{0, 1};{0, 1}         //========================// MORE INFORMATION ================================================================================= If you want for rt61 driver to auto-load at boot time: A) choose ra0 for first RT61 WLAN card, ra1 for second RT61 WLAN card, etc. B) go to "./RT61_Linux_STA_Drv_x.x.x.x/Module" directory.    $make install NOTE:         if you use dhcp,         add this line         BOOTPROTO='dhcp'         in the file ifcfg-ra0 . *C) To ease the Default Gateway setting,     add the line     GATEWAY=x.x.x.x       in /etc/sysconfig/network    감사합니다.

[2007-01-02 17:11:25]
목록보기
▲갑자기
▼무선인터넷이 안됩니다
챗봇 상담
설치도우미 바로가기
펌웨어 업그레이드 바로가기
펌웨어 복구도우미 바로가기
ipTIME 검색기 바로가기
EasyMesh 접속기 바로가기
ipDISK ipCloud 바로가기
ipCAM Tools 바로가기
DDNS 관리 바로가기

경기도 용인시 기흥구 죽전로 15 6층 (보정동, 벤포스타2빌딩 6층)

통신판매업신고번호 : 용인 기흥 제 388호
사업자등록번호 : 129-81-44050 | 대표자 : 김인

ALL contents are copyright 2004-EFM Networks Co
All right reserved