답변[re] 방화벽 및 80포트 문의

안녕하세요~ 최정환 고객님, ipTIME 기술팀 입니다. 추가 문의사항에 대해 답변드리겠습니다. 공유기와 연결된 PC의 경우 외부접속경로에 대해 공유기상에 특별한 방화벽은 존재하지 않습니다. 포트개방설정의 경우 포트포워설정을 통해 가능하며, 공유기설정화면(http://192.168.0.1)에 접속하여 관리도구 - 고급설정 - NAT/라우터관리 - 포트포워드설정에서 정의된 리스트 : HTTP 선택 내부ip주소 : 현재 접속된 PC의 ip주소로 설정 체크 [추가] 를 클릭하시면 80포트는 해당PC로 개방됩니다. 감사합니다. >>> 최정환 님이 쓰신 내용 <<< > >안녕하세요~ 최정환 고객님, ipTIME 기술팀 입니다. > >문의주신내용에 답변드리겠습니다. > >공유기 교체 후 특정프로그램이나 특정사이트 접속이 원활하지 않는다면 인터넷회선을 해당PC에 다이렉트로 연결하여 정상동작유무를 확인하시기 바랍니다. > >정상동작이 확인되신 이후에는 N104A 를 연결 후 아래와 같은 방법으로 MAC클론 설정을 진행해주시기 바랍니다. > >MAC 클론(고객인증 방식/케이블 인터넷 사용시)  <<<   클릭하세요 > >감사합니다. > > >>>> 최정환 님이 쓰신 내용 <<< >> >>안녕하세요. >> >>orb.com 이라는 사이트에서 제공하는 오르브라는 프로그램을 사용했습니다. >>다른 컴퓨터에 있는 동영상을 보는 프로그램입니다. >> >>Q504 제품을 사용할 때는 잘 연결이 되더니 >>N104A 제품으로 바꾼 후에는 방화벽이 설치되어 있다는 오류메세지가 뜹니다. >> >>Q504 제품을 사용할 때 아무런 설정변경 없이 사용했었는데 >>N104A 제품도 Q504 제품의 설정으로 똑같게 만들려면 어떤 것을 수정해야 하나요? >> >>꼭 답변 부탁드립니다. > > > >위와 같이 해봤는데 MAC클론으로 해결되지 않았습니다. > >오르브 프로그램 해당 사이트에서는 방화벽을 해제하고 80포트도 열어 놓으라고 하는데 >N104A에서 방화벽을 해제하는 방법을 알려주세요. > >참고로 아래는 해당사이트의 트러블슈팅 내용입니다. > >How do I configure my firewall to allow incoming and outgoing traffic for Orb streaming? >Print      Email to friend > Rate it Useful Useless   >Views: 69795 >Votes: 44 > >If you have a software firewall (other than the built-in Windows firewall) on your Orb PC then you will need to create incoming and outgoing traffic rules to enable Orb streaming from that PC to either an Internet-connected device or a device within your Local Area Network (LAN), such as another PC, a laptop, a PDA, or a game console (Nintendo Wii, Sony PS3, etc.). > > >Every UI and navigation will be different so, if your firewall software is not among the five listed below, refer to your firewall help guide for specific step-by-step instructions on how to create incoming and outgoing traffic rules for the three Orb applications: Orb.exe, OrbTray.exe and OrbStreamerClient.exe. > > >The ports you need to open on your Orb PC are: > > >     For Windows media (WMP, WinAmp, TCPMP, or Flash Player): TCP port 80 (or port 81, if you have another program like Skype running on your Orb PC. > > >     For Real media (RealPlayer): TCP port 554 and UDP port 13398 > > >     For 3GP media (Quicktime or other 3GP player): TCP port 554 and UDP ports 13398 to 13401 > > >Examples of how to create incoming/outgoing traffic rules on five selected Firewall software: > > > McAfee Security Center > > >1.   Open up the McAfee Security Center > > >2.   Click Internet & Network located in the main panel of the McAfee Security Center window, then click the Configure link > > >3.   Click the Firewall protection is enabled bar to expand this selection, then click the Advanced button > > >4.   Click the Program Permissions link on the left-panel menu > > >5.   In the Program Permissions list, find and click Orb.exe > > >6.   Click Grant Full Access. This will allow all inboud and outbound traffic to this program > > >7.   Repeat Steps 5. and 6. for OrbTray.exe and OrbStreamerClient.exe > > >8.   Click OK. You're done! > > > Norton Personal Firewall > > >1.   Open up Norton Protection Center > > >2.   Click the Norton Internet Security tab > > >3.   Click Settings to expand the selection, click the Personal Firewall link to further expand this option, then click the Configure button > > >4.   Click the Program Control link on the left-pane of the window > > >5.   In the Program list, click Orb.exe to select it, then click the Modify button. (Note : if you do not see this program listed, click the Add button and browse to the "C:Program FilesOrb NetworksOrbbin" folder to fetch it) > > >6.   Click the Direction: In/Out rule, then click the Modify button > > >7.   Select the Allow radio button, then click the Connection tab > > >8.   Select the Connections from other computers radio button, then click the Computers tab > > >9.   Click the Any Computer radio button, then click the Communications tab > > >10. The protocol you want to allow should be TCP and UDP by default. Select the All types of communication radio button. (Note : your other option "Only communications that match all types and ports listed below" requires you to create 3 separate rules to specify the 3 sets of ports listed above (i.e., 80, 554, and 13398 to 13401) > > >11.  Repeat Steps 5. to 10. for OrbTray.exe and OrbStreamerClient.exe > > >12.  Click OK to save these rules. You're done! > > > ZoneAlarm Pro > > >1.   Open up ZoneAlarm pro > > >2.   Click Program Control on the left pane of the window, then click the Programs tab > > >3.   In the Program list, find and click Orb.exe to select it, then click the Options button. (Note: if you do not see this program listed, click the Add button and browse to the "C:Program FilesOrb NetworksOrbbin" folder to fetch it) > > >4.   Click the Expert Rules tab, then click the Add button > > >5.   Enter the following: > Rank: 1 > Name: Orb1 > State: Enabled > Action: Allow > Rank: 1 > Source: click Modify and enter: >Protocol: TCP & UDP >Description: Orb1 >Destination Port: 80 >Source Port: 80 > > >6.   Repeat 5 above but, this time, use Orb2 as "Name" and Description", and Port 554 for both "Destination Port" and "Source Port" > > >7.   Repeat 5 above but, this time, use Orb3 as "Name" and Description", and use the Modify button in the "protocol" section to add Ports 13398 to 13401, then set them as your "Destination Port" and "Source Port" > > >8.   Repeat Steps 5. to 7. for OrbTray.exe and OrbStreamerClient.exe > > >9.   Click OK to save these rules. You're done! > > > Trend Micro PC-cillin > > >1.   Open up the Trend Micro PC-cillin Internet Security >   > >2.   Click Personal Network & Firewall Controls on the left pane of the window, then click the Programs tab > > >3.   Click the Personal Firewall header to expand the section, then click the Settings button > > >4.   Click the Direct Internet Connection (if configuring for Internet streaming) or Home Network (if within your LAN) option. Then click the Edit button > > >5.   Click the Program Control tab at the top of the screen, select Orb.exe in the list of programs, then click the Edit button. (Note: if you do not see this program listed, click the Add button and browse to the "C:Program FilesOrb NetworksOrbbin" folder to fetch it) > > >6.   Click the Simple Mode radio button to keep the following default configuration: >Connection : In >Action: Allow >Protocol: TCP/UDP   > >Port/Type: Any > > >7.   Repeat Steps 5. and 6. for OrbTray.exe and OrbStreamerClient.exe > > >8.   Click OK to save that rule. You're done! > > > Lavasoft Personal Firewall > > >1.   Open Lavasoft Personal Firewall > > >2.   From the top menu, click Options, then Application > > >3.   Find and select Orb.exe from the list of programs. (Note: if you do not see this program listed, click the Add button and browse to the "C:Program FilesOrb NetworksOrbbin" folder to fetch it) > > >4.   Click the Create Rules button if you found OrbStreamerClient.exe under "Blocked applications", or the Modify Rules button if you found OrbStreamerClient.exe under "Partially allowed applications". > > >5.   Click the New button, then select: > >    Event >Where the specified protocol is >Where the specified direction is >Where the specified local port is >    Actions: Allow it >    Rule Description - > >Click "Undefined" for "specified protocol" and enter TCP >Click "Undefined" for "specified direction" and enter Inbound > >Click "Undefined" for "local port" and enter 80 >    Give a Rule Name like "Inbound TCP for Orb 1" for example >    Click OK >    Repeat 5 and create a new rule for each one of the Orb ports you need to open, as specified above. Make sure you create an Inbound and Outbound direction for each port > > >6.   Repeat Steps 3. to 5. for OrbTray.exe and OrbStreamerClient.exe > > >7.   Click OK to save these newly created rules. You're done! > 감사합니다.